English
Pусский
Español
Tiếng Việt

Home » News » News » Industry » Preventing Flex-Line Cracking: High-Cycle Bally Dynamic Flexing Evaluation for Waterproof Leathers and Synthetics

Preventing Flex-Line Cracking: High-Cycle Bally Dynamic Flexing Evaluation for Waterproof Leathers and Synthetics

Publish Time: 2026-11-11     Origin: Site

A waterproof boot may face wet grass, rain or a wash-down floor long before the wearer notices a problem. If the upper develops cracks along a repeated flex line, the damage can affect its appearance and may expose other layers of the construction to moisture.

For footwear manufacturers, the challenge is to find weaknesses while materials are still being selected—not after finished products reach customers. Bally flex testing gives product development and quality teams a controlled way to compare how upper materials respond to repeated bending.

Why Flex-Line Cracking Matters

Every step bends the upper, particularly across the forepart of a shoe. Over time, creases form in the material and its surface finish. Depending on the construction, repeated movement can lead to fine surface cracks, coating damage or more extensive deterioration.

The cause is not always obvious from an unused sample. Two materials may feel similarly soft and pass an initial visual inspection, yet behave differently after repeated flexing. Differences in the leather, synthetic backing, coating or finish can all be worth investigating when one sample begins to show damage earlier than another.

For water-resistant footwear, a crack in the outer material deserves attention. Whether it leads to water entering the shoe depends on the complete construction, including membranes, seams and other layers. That is why flex resistance and water resistance should be assessed separately.

How a Bally Flex Test Works

A Bally flexometer repeatedly bends a prepared material specimen between grips. The test creates a crease in a controlled way, allowing the laboratory to examine how the material and its finish change as the cycle count increases.

Under SATRA TM55, specimens are inspected at specified intervals and the number of flexing cycles is recorded. The method applies to flexible materials, including leather, coated fabrics and textiles used in footwear uppers.

For a useful comparison, the laboratory should record more than the final cycle count. The first appearance of fine cracks, changes in the surface finish and the extent of damage at each inspection can all help a development team distinguish between materials.

The required number of cycles and the acceptable level of damage depend on the relevant test method, product specification and buyer requirements. A result at 50,000 cycles, for example, is meaningful only when those conditions are clearly defined.

What Quality Teams Should Look For

When inspecting a flexed specimen, the first sign of a problem may be subtle. Depending on the material, useful observations include:

  • Fine cracks along the crease: Note when they first become visible and whether they grow with further flexing.

  • Damage to the surface finish: Look for flaking, peeling or other changes around the bend.

  • Changes in the underlying material: Check whether damage appears limited to the finish or extends into the material beneath it.

  • Differences between specimens: Variations within the same batch may warrant further investigation.

Photographs taken at consistent inspection intervals can make it easier to discuss results with material suppliers and compare new batches with previously approved samples. The report should identify the material, test conditions, cycle count and inspection criteria.

the GW-001 Bally Flex Tester

The Great Win GW-001 Bally Leather Flexing Testing Machine is designed for repeated flexing tests on materials such as leather used in footwear uppers. It has 12 sets of flexing grips and a digital counter, allowing laboratories to test multiple specimens and record the number of cycles.

This makes it useful for comparing incoming leather batches, reviewing a change in finish or evaluating candidate materials during product development. For synthetic or coated materials, confirm the appropriate grips, method and test setup for the material and specification before testing.

Bally flexing is one way to examine material damage under repeated bending. It does not reproduce every aspect of a shoe’s movement in wear. Where a buyer requires a different flex method—or where a test more representative of the footwear’s vamp movement is needed—the laboratory should select the method accordingly. SATRA discusses the differences between Bally and vamp flex testing.

Flex Resistance and Water Resistance Answer Different Questions

A material can be examined for cracking after flexing without measuring how much water passes through it. Conversely, a water penetration test examines a different property under its specified conditions. Both may be relevant when developing footwear intended for wet environments.

At the material level, SATRA TM34, known as the Maeser method, assesses resistance to water penetration while a specimen is flexed. Great Win’s GW-012 Maeser Flexing and Waterproof Testing Machine is designed for water penetration testing under flexing.

Finished footwear needs its own assessment. Seams, the connection between upper and sole, membranes and other construction details can influence whether water enters a shoe. The GW-014 Dynamic Waterproofness Tester is designed to assess water resistance while footwear is immersed and flexed.

The appropriate combination of material and whole-shoe tests depends on the product’s intended use and the requirements of its target market or customer.

Turning Test Results Into Better Material Decisions

Flex testing is most valuable when it helps the team make a decision. If a sample develops early surface cracks, compare it with an approved reference and review any differences in material, finish or processing. If results vary within a batch, further sampling may help determine whether the issue is isolated or more widespread.

For development teams, the same approach can be used before a material is approved: agree on the test method and inspection intervals, record the type and extent of damage, and compare the findings with the product’s requirements.

Looking for equipment for your footwear materials laboratory? Explore the GW-001 Bally Flex Tester or contact Great Win at Vincent-zhong@greatwin-test.com to discuss your testing application.

Related News

Phone:
0086-0769-82767811
0086-13929200954
Address:
A6,Huazhi high-tech park,Yongqing Village,Daojiao Town,Dongguan City,Guangdong Province , China
About Us
Great Win Testing Machine CO. Ltd was set up in 1999, it has been over 20 years' history in the field of professional experience for lab testing instrument such as Footwear Testing Equipment, Leather Testing Equipment, Textile Testing Equipment, Toy Testing ...
Latest News
Safety Shoes Testing machine have special function for shoes quality control

The safety footwear industry requires specialized testing equipment to ensure that safety footwear products meet the required safety standards and provide adequate protection for workers.

Subscribe
 Sign up for our newsletter to receive the latest news.

© 2021 Great Win Testing Machine CO. Ltd All rights reserved. Technology By Leadong.com | Sitemap